windowcurtain

window accessories ideas
Menu
  • Home
  • window box
  • window coverings
  • window curtains
  • window interior
Home
window coverings
How To Install Wellcraft Window Well Cover
window coverings

How To Install Wellcraft Window Well Cover

May 23, 2022

Wellcraft offers a co. Well covers protect access to egress wells and prevent anything or anyone from accidentally falling in.


Window Well Cover Wellcraft 5600 Polycarbonate Flat Egress Mainline Materials

Be sure to properly install a Wellcraft Egress Window Well Cover.

How to install wellcraft window well cover. Determine the vertical mounting location. The Wellcraft 2062 Flat Window Well Cover is designed for smaller egress single unit wells and is made from tough polycarbonate plastic that can support up to 500 lbs of load. Covers also keep leaves and debris from clogging up the egress.

If playback doesnt begin shortly try restarting your device. On both sides of the cover measure about 4 in. Wellcraft window wells should be installed with the top edge of the well above the top edge of the window so that the well does not interfere with the window opening and to allow the cover to fit properly.

The Dome style covers securely hold up to 350 pounds. WINDOW WELL COVER INSTALLATION Fasten flat brackets to cover flange at holes provided with slotted end of bracket pointing as shown. The unit comes with a fastener system engineered to withstand hurricane-force winds and is still easy to remove when necessary.

Assemble The Window Well Frame. Installing A Window Well Guard. Sizing Options Sections Total Height 1 2078 2 3478 3 4878 4 6278 5 7678 grey 056100092.

Easily opens from both the inside and outside. The steps should be at the top of each section when installed. Secure a cover on top of the well to prevent anything from getting inside.

Then measure out 32 and mark the location. A typical installation uses four sections and is easy to install. Each section weighs only 24 pounds and is easy to transport.

Mark on both sides of your well. For each model a clear polycarbonate cover is available which allows sunlight in. Egress wells must be installed in all.

Get a window well cover that matches the size of your window well and place it over the opening. Set cover in place against house wall and on top of the window well casing. If you want the cover permanently installed make holes in your foundation with a hammer drill and a masonry bit before securing the cover in place with anchors.

You will be installing 4 Dual-Lock discs to your well and cover. For non-egress windows measure tape and mark the covers at the sides and in the front if the cover uses more than two clips. The design of our covers is very simplistic helping to relieve any stress that might be caused by a confusing well cover making installing your window well cover even easier.

Lay two 24s on the ground parallel to each other that are spaced out by half the width of the window well. Eliminate constant cleaning. Mark proper location for bending brackets and then bend as indicated.

Window well escape systems may be a safety requirement but you dont have to sacrifice your basements beauty to comply with the code. This ensures the attachment hardware will be ush with. Window well covers help sustain a beautiful look and clean environment by keeping out leaves and other unsightly debris.

-Both on the inside of the well-Two 8 from the foundation -Two 22 from the foundation Image 1 2 Use a marker and mark all four locations to drill. Designed for easy emergency escape. Crystal-clear UV-inhibited polycarbonate provides natural light to basement.

The unit comes with a fastener system engineered to withstand hurricane-force winds and is still easy to remove when necessary. Wellcraft window wells should be installed with the top edge of the well above the top edge of the window so that the well does not interfere with the window opening and to allow the cover to fit properly. Unobstructed sunlight to reach the basement.

Handmade Window Well Covers. The 5600 is designed for windows up to 4-foot wide. The top edge of the well should also be approximately 3 inches above final grade.

Designed with safety in mind Wellcrafts egress window well covers allow homeowners to easily escape in an emergency while protecting children and animals from accidentally falling in. Use a single screw to attach the 14. Determine the vertical mounting location.

Wellcraft is not responsible for accidents caused by failure to have a well cover installed. Wellcraft window wells should be installed with the top edge of the well above the top edge of the window so that the well does not interfere with the window opening and to. Drill 14 holes through window well casing at the desired locations.

Then mark the tape where the window-well edge touches the cover. While Wellcraft Egress Window Wells ensure that those inside your home are safe dont neglect those outside – like children neighbors and pets – who might accidentally step into an open well. TM Center your Dual-Lock TM TM TM TM Place your cover over the well.

Using the provided self-tapping screws attach all the hardware for your cover. Learn how to install a window well in the link below. Simply mark the locations your mounting clips will be installed make sure these marks are even throughout the cover and then drill a hole at these marked locations.

Lay one 14 across one end and a second 14 across the other end. 2060 Single Unit Well. If a well was installed on an existing window you must make sure to use a Wellcraft dome style cover to ensure safety around the well.

The top edge of the well should. Use a marker to mark the location of the Dual-Lock disc. 34 inch plywood plexiglass vinyl lattice polyurethane screws and siding are the only supplies required for this fantastic DIY window well cover.

A Wellcraft cover should always be installed to prevent people and animals from stepping into the open well. Image 2 Make sure your hole is a 12 below the top lip of the well. From the edge thats against the house and mark those locations with painters tape.

Be certain to attach the Dual-Lock in the center of the well wall. The Wellcraft 5600 Dome Window Well Cover is made from tough polycarbonate plastic that. The Wellcraft 2060 Flat Window Well Cover is designed for 4-foot single unit wells and is made from tough polycarbonate plastic that can support up to 500 lbs of load.

Our Flat covers support up to 500 pounds. Allow each 14 to hang 1 inch off the end of the 24 so that it can act as a catch.


5 Easy Steps To Install Window Well Covers


5 Easy Steps To Install Window Well Covers


Window Well Covers Wellcraft Egress Systems


About Us Wellcraft Egress Systems


Wellcraft Model 5600 With Polycarbonate Dome Cover Installed By Egress Systems Inc Egress Window Well Egress Window Window Well


Window Well Cover Wellcraft 5600 Polycarbonate Flat Egress Mainline Materials


Window Well Covers Wellcraft Egress Systems


Wellcraft Wells Egress Solutions Inc


Wellcraft 5600 Series Modular Window Well Section From Buymbs Com

Share
Tweet
Email
Prev Article
Next Article

Related Articles

Neat and functional like it. Im looking for a roll-up …

Insulated Window Covers For Home

1 pc of corrugated black plastic 24×36 sku 074507996159 922. …

Travel Trailer Front Window Cover Replacement

About The Author

Leave a Reply

Cancel reply

Recent Posts

  • Diy Interior Window Insulation
    June 11, 2022 0
  • Plastic Shutters For Windows Interior
    June 11, 2022 0
  • Upvc Internal Window Sill Joint Covers
    June 11, 2022 0
  • Farmhouse Interior Window Trim Ideas
    June 11, 2022 0
  • Interior Window Trim Kit Home Depot
    June 10, 2022 0

Popular Posts

    windowcurtain

    window accessories ideas
    Copyright © 2023 windowcurtain
    Theme by MyThemeShop.com

    Ad Blocker Detected

    Our website is made possible by displaying online advertisements to our visitors. Please consider supporting us by disabling your ad blocker.

    Refresh